how do i run monitors to stage? need 4 monitors on stage, what are my options.

You can use up to 4 separate monitor buses, but this mixer works best if you use Aux buses 1 and/or 2 as monitors because these are "pre-fader" outputs (which means you won't risk getting feedback from the monitor if you increase the channel fader volume). Use the 1/4" phono jacks labeled "Aux Send" and run these to your POWERED MONITORS ( or to the input of a power amp for your monitors). Adjust the volume of each channel in the monitor mix by adjusting the knob labeled "Aux 1" or "Aux 2". Adjust the overall monitor volume using "Aux Send 1, 2" gain knobs on the right side of the board. If you want to run the same mix to all of your monitors, just use Aux 1, and then daisy chain it from one powered speaker to the next (if your powered monitors have a signal out jack. Otherwise, you will need to split the output using "Y" connectors.I run 4 powered monitor speakers on 2 Aux Buses (Aux 1 and Aux 2). Aux 1 is for the front line of the band, so I wire from the Aux Send 1 jack to the Front Left monitor, then daisy-chain from that speaker to the front right speaker. Aux 2 is for the rhythm section, so I wire from the Aux Send 2 jack to the Rear Left monitor, then daisy-chain from that speaker to the rear left monitor.I use a different monitor mix for front/back of the band because we sometimes use backing tracks, and I want these louder for the rhythm section, so they can stay sync'ed with the track.You could use all 4 Aux Sends so that each monitor had a different mix but 1) That gets really complicated to sound check, and 2) Aux Send 3 is used for Effects, so using it as a monitor channel would mean you can't use the mixers effects. and 3) Aux Sends 3 and 4 are Post-Fader, which means they are affected by the channel fader, which means if you adjust the fader for the mains, say to bring up a vocalist, you are also bringing them up in Aux 3 and 4, which could mess up the on stage mix, and cause all kinds of havoc.Hope that helps.

Do you know what kind of mixer rack case this will fit with the rack rails?

This is what I have it installed in:http://www.musiciansfriend.com/accessories/odyssey-cxp1110w-carpeted-pro-combo-case-w-wheels?skuId=site1sku804787000000000

My USB out is only mono. The manual is very unfriendly. Help?

Here's what the manual states: The XENYX mixer line has built-in USB connectivity, allowing stereo signals to be sent to and from the mixer and a computer. The audio sent from the mixer to a computer is identical to the MAIN MIX. Audio being sent to the mixer from a computer can be routed to the main mix with the 2-TR/USB TO MAIN button. Connect the USB type B plug into the USB jack on the mixer, and the other end into a free USB port on your computer. There are no required drivers, but we recommend that PC users install the included ASIO driver. The driver can also be downloaded from behringer.com.I don't know what OS you are using, but you might want to make sure that your computer is set up for stereo input/output via your preferences. You could also check to see if you have the correct drivers installed from Behringer, and lastly, make sure you have the 2TR/USB to MAIN properly depress and you can also route it to a set of headphones via the SOURCE 2TR/USB. Also not sure if this is what you are hearing through headphones or mains (?). Are your main channels routed independently? So when you say USB Out, is that from a stereo source or from the PA?

Product Dimensions	43.99 x 42.01 x 13.49 cm; 5.9 kg
Item model number	X2442USB
Hardware Interface	USB
Power Source	Corded Electric
Voltage	240 Volts (AC)
Item Weight	5 kg 900 g
Manufacturer	Behringer
Country of Origin	China
Imported By	Alphatec Audio Video Pvt Ltd

Behringer XENYX X2442USB Premium 24-Input 4/2-Bus Mixer with XENYX Mic Preamps & Compressors

Details

Description

Specifications

Have a Question? See What Others Asked

Common Questions