Rubber Bottle Jack Pad Protector Support Point Adapter Car Jacking Tool Pinch Weld Side Lifting Disk 29mm 1 1/8“ Hole 2/5-8t Hydraulic Jacks

This product is about as simple as they can get. A rubber disc that attached to the top of your bottle jack in order to increase the load area and reduce metal to metal contact. Essential if, like me, you value your car.The rubber seems good, dense and solid and will hopefully hold up to frequent use. I would add that personally I would always look for a flat area on the underside of the car as putting this directly under a vertical edge could perhaps cut into the rubber or cause it to split.I have several bottle jacks and a point to note is that this doesn't fit them all. The top of your jack needs to be 25mm - it might be greater than this if the ram has an added 'cap' already.Pricey for a bit of rubber but well worth the money to protect your car from possible pressure damage by jacking without a pad.

This is one of those useful products that you wish had been widely available in the past. The rubber disk simply sits on top of your trolley jack or bottle jack lifting pad, preventing damaging metal-to-metal contact on the underside of your vehicle. In the past, I have used ice hockey pucks to 'cushion' the tops of jack pads and axle stands - but they tend to split and crack wherever they rest on any projections or seams under the vehicle.... this handy product has a ready-cut pattern of grooves in the top surface, which allow the pad to be fitted along and over pinch-welds without risking splitting the whole pad. There is also a 25mm cut-out on the underside of the pad, which helps it to sit securely on those jacks which have tops of matching size. A very big plus for this product is its current price-point - but my only concern is that the material this pad is constructed does not feel quite as hard as the ice hockey pucks I previously used..... only time will tell whether it will last longer in use.

I do servicing of my car by myself. I normally use a trolley jack, and a bottle jack for quick jobs. I do not like the load on the small area, which could cause deformation to the car body or coating damage leading to corrosion later. So I prefer to use wood or rubber pads. Wood breaks very fast. I have a Lidl jack. This rubber protector fits nicely on the jack. The rubber is hard and strong and does not deform under load or damaged by the bottle jack. It has a diameter of 60 mm and hence distributes the load in a much bigger area. As it’s not too thick you will not have difficulty to put the jack with the rubber pad below the car. I have tried different rubber pads previously. Some deform and break on first use. But this one is really good and lasting. Highly recommend, if you do not want to deform your car body.

This is a strong sturdy hard rubber top for a bottle jack designed to spread the load and increase the grip. Unfortunately I didn’t measure my 2t jack and the opening in the bottom was too small ( this one as stated is for a jack with a 1” ( 25mm ) top, mine has a 30mm top.Luckily I have small lathe and was able to open the hole up to fit 🙂Good value for money, but do double check the size of your jack top first !

Worked as expected, safer than metal to metal.

The Rubber Bottle Jack Pad Protector Adapter Car Jacking Tool Pinch Weld Side Lifting Disk 25mm Hole For Most 3-4 Ton Bottle JacksBrand: AUTOXBERT in every resealable packet.Are we getting the packet is just one round rubber puck, that sits on top of a bottle Jack or a trolley jack.I've had so many of these over the years and they are worth their wait in gold! It saves your seals from all getting crushed and bent because the rubber protects the seals and stops the metal from bending.The amount of seals that I have seen on cars that have been destroyed due to improper use of jacks is unbelievable!This product solves most of them issues if used correctly.And at this very low price I would say it's well worth the money because it saves you from costly repairs due to bent seals with improper use of jacks.Great product! ⭐⭐⭐⭐⭐

What can I say. It is exactly as described in the listing. A good quality very dense rubber pad to protect the vehicle from damage or slippage and to spread the lifting surface area. It goes between the Jack top and the car itself. If I was to be a bit picky, I would have liked to seen a deeper slot on top to accommodate welded seams a but better on cill lifting points. Otherwise a nice well made product.

First off 2 tons is not the same as 2 tonnes and 2T doesn’t mean much. A ton (British) is an imperial 2,240 pounds or 1,016.047 kg. An American ton is lighter at 2000 pounds. A metric tonne is 1000Kg. This pad for a bottle jack which I expected would work ok on an old and rarely used bottle jack I have. However, on the underside, it has a round cut-out of 20mm diameter that won’t fit on my old bottle jack because the top of my jack is approx 40mm diameter. The top of my jack is also wider than ram section of my jack which is approx 25mm and I ‘discovered’ my jack is rated at 3 imperial tons. I guess if you have a new bottle jack with a ram of 20mm diameter and a top pad of the same size as the ram it would work for you. Looking at new jacks I didn’t see the ram or top size quoted so you’d need to check that first. I can’t give this product more than 1 star because it didn’t work on my jack and I couldn’t test it.