SmartStandard 30in x 84in Sliding Barn Wood Door Pre-Drilled Ready to Assemble, DIY Unfinished Solid Spruce Wood Panelled Slab, Interior Single Door Only, Natural, K-Frame (Fit 5FT Rail)

I initially considered crafting my own barn door, but after evaluating the costs of materials alone (excluding my time) the precut barn door kit emerged as the better option.The assembly process was surprisingly swift, taking 15-20 minutes to complete. The door's design features intuitive notches that ensure the pieces interlock seamlessly, secured firmly with screws. The central panels, also notched, slide in effortlessly without leaving any gaps, although ensuring good alignment and squareness helps with this.To conceal the screw holes, the kit includes pegs, and for those who prefer, decorative overlays can be added towards the end using the provided screws.One crucial tip: the door's bottom is pre-cut to accommodate a track guide, so it's important to position it on bottom during assembly. Keep in mind, the hardware for hanging the door is sold separately, necessitating drilling for the barn door rollers.My sole concern is the center panel's material, which is somewhat thinner and less resilient. You can feel it flex when you push on the door. It does its job but I could see kids rough housing and breaking the center section.

This was easy to assemble and made a good looking job.

Easy to assembly. Look beautiful with just a single stain coat. My husband and me we are very happy with the final results! See pictures and judge by yourself.

This barn door was wonderful. It was packaged very well and easy to put together. We noticed that there was some spacing between the boards when we put it together. Although the directions said it was normal and the wood would expand as the days went on, we felt the spacing was too much so we added some double sided tape to the inside groove of one of the long outside board. You will see there is a foam piece in the groove already, so we just stuck a piece of tape to it. We didn't take the paper off the other side of the two sided tape and then we put the boards back together. It seemed to work beautifully and hopefully the boards don't expand. The wood did not have a lot of knots and we were hoping to stain it, but we felt it looked better painted in our room. It truly would have been a beautiful door if we had stained it too. We put the "K" frame on the bedroom side of the door, but left it off the bathroom side of the door. If we notice the boards start to "cup", we will install the "K" frame on the bathroom side as well. I have attached pictures from both the bedroom and bathroom side so you can see what it looks like. To finish the door, first I rolled a coat of primer on the door and followed it up with three coats of white semi-gloss with primer, so I'm hoping the knots don't ever come through. Our walls are painted Sherwin Williams, color number 0055, Light French Grey. We feel this was a great purchase and would highly recommend it.

I bought 3 of these. 2)36" and 1) 42". Had I only purchased the 2)36's I would be telling you this was the EASIEST "Assembly required" item I had ever done. They are well cut and extremely easy to assemble. But the 42" gave me a lot of grief. There seemed to be a little humidity that caused a SMALL amount of warping. But that made assembly much more difficult. I was lucky that I own some cheap, but long, clamps (Harbor Freight $20) And that made all the difference. I assembled the two 36 in first..Super easy. But I might have sent the entire batch back if I had reversed the order, based on the 42 in. I saved about $600 on premade doors, so it was worth the trouble. You dont need to be "Mr Handy" to assemble them. But a little skill with a hammer drill is a good thing. One final thought... The 36 in doors are 36x80. The other is 42x 84!!!! 4 inches taller! Something I didnt realize until I was done assembling and stood it up. All 3 of these go on the same wall. I am not sure how I will make it look correct with a 4 inch difference. So beware if you are mixing and matching.

These doors are unbelievable how great they are for the price. We took a few hours because we read all instructions and made sure we adjusted so nothing was sticking out before putting the long screws in. Also note that the smaller slats do have a left and right also so make sure to read what is bottom and what is top and what goes to the left and to the right. We’re still deciding on the diagonal piece and how we want it. The only complaint I have is that a piece was broken from shipping but we managed to put in the side you don’t see.

This is a very nice door and easy to put together for the full 80 inch height. I had to shorten it however to 78 inches. My wife cut all the center boards by 1 inch and the 2 side boards by 2 inches. I had to lengthen the side board middle slots by 1 inch and the top slots by 2 inches. It would have been easier if the middle and top slots were already longer, but it worked out anyway. I’ll be hanging this from a rail attached to a 82 inch high ceiling. My first thought was a custom made door. This 80 inch door was close enough to what I needed that I thought I’d take a chance. The answers to comments said it couldn’t be cut down but that depends on how determined you are.